MCDP2850-BC中文资料芯凯电子数据手册PDF规格书

特性 Features

• DisplayPort™ (DP1.2a) receiver

– Link rate HBR2/HBR/RBR

– 1, 2, or 4 lanes configuration

– AUX CH 1 Mbps, HPD out

– Supports eDP ASSR scrambler operation

• HDMI2.0b transmitter

– Max data rate up to 6.0 Gbps/ch

– Deep color up to 16 bits per color

– 3D video timings, CEC, HPD in

– Supports High Dynamic Range (HDR)

– Supports scrambling for the higher data

rate

• Level shifter operation (up to 3.4Gbps/ch)

– AC-coupled HDMI1.4b to DC-coupled

HDMI1.4b

– PHY analog repeater (re-driver or retimer)

– 3.3 V DDC/AUX CH signaling support with

auto detect

– 3.3 V DDC to 5V DDC buffering

– I2C-over-AUX to 5V DDC translation

– DP HPD_OUT matched to HDMI HPD_IN

• Protocol converter operation (up to 6.0

Gbps/ch)

– DP SST-to-HDMI format conversion

– Video and audio forwarding

– Pixel encoding format conversion from

YCbCr444 to YCbCr420

– Horizontal expansion of VESA CVT to

CEA-861 timings

– Meta data handing

• Level shifter – Protocol converter mode

switching

– Via sideband communication (AUX CH/

DDC)

• Max video resolution and color depth

– 4Kp60Hz, RGB/YCbCr444, 8bpc

– 4Kp60Hz, YCbCr420, up to 16bpc

– 4Kp30Hz, RGB/YCbCr444, up to 16bpc

• YCbCr420 support

– YCbCr444-to-420 conversion, up to 16

bpc

– YCbCr420 pass through, up to 16 bpc

• Stereoscopic 3D forwarding

– Conversion from frame sequential over DP to

stacked top-bottom 3D over HDMI

– All other 3D formats forwarded as is

• Audio forwarding

– 2-ch, 768 kHz 24bps HBR audio

– Up to 8-ch, 192 kHz, 24bps LPCM audio, AC3,

DTS

• Secure communication

– Intel secure communication protocol compliant

with LSPCON spec

• HDCP content protection

– Embedded HDCP keys

– HDCP2.2 transmitter

– HDCP1.x repeater

• Metadata handling

– HDMI TX DVI/HDMI mode setting (DPCD

register)

– YCbCr444-420 conversion (DPCD register)

– IEC60958 BYTE3 channel status overwrite

– CEA861F INFOFRAME generation

– CEA861-3 HDR and Mastering InfoFrame

• SCDC read request handling

– Polling enabled for HDMI sinks not supporting

read request

• AUX to I2C bridge for EDID/MCCS pass through

• CEC tunneling over AUX CH

• Device configuration options

– SPI flash for firmware binary image storage

required

– AUX CH, I2C host interface (optional)

• EMI reduction support

– Spread spectrum for DP input

– Scrambler for DP input and HDMI2.0b output

• Low power operation

– 412 mW in protocol converter mode

– 100 mW in Level shifter mode

– 0.1 mW in connected standby mode

• ESD specification

– 6.5 kV HBM, 500 V CDM

• Package

– 64 LFBGA (7 x 7 mm)

• Power supply voltages

– 3.3 V I/O; 1.2 V core

Applications

• PC notebook/ tablet motherboard

• DP/USB Type-C docking station, dongle

1. Description

The MCDP28x0 is a power-optimized DisplayPort1.2a-to-HDMI2.0b converter device targeted for

desktop/mobile PC motherboard-down applications and for DP or USB type-C adaptor (dongle, docking

station) applications. This device functions as a level shifter as well as an active protocol converter.

In level shifter mode, the device functions as a PHY repeater with optional jitter removal capability. This

operating mode provides a low-power means of using an AC-coupled TMDS signal from a dual mode DP

(DP++) source to be repeated to the HDMI output. The maximum TMDS character clock frequency in this

mode is limited to 340 Mchar/s (per HDMI1.4b specification).

In Protocol Converter (PCON) mode, MCDP28x0 functions as a DP branch device receiving AC coupled

DisplayPort stream and converting it to HDMI output. The maximum TMDS character clock frequency

supported in this mode is up to 600 Mchar/s (as per the HDMI2.0b specification).

The MCDP28x0 operates with two power supply voltages: 1.2 V and 3.3 V. It consumes:

• 100 mW in PHY analog repeater mode

• 412 mW in protocol converter mode

• 0.1 mW in connected standby mode (1.2 V power rail disabled)

The MCDP28x0 has a DisplayPort1.2a dual-mode receiver and HDMI2.0b transmitter. The upstream

main link can receive DP input at HBR2 rate over 4 lanes and AC-coupled TMDS signal up to

340Mchar/s. It supports DP SST stream on its main link and Manchester-coded AUX signaling or native

3.3 I2C signaling as the side band channel with the DP++ source. The downstream HDMI TX port is

HDMI2.0b specification compliant.

The MCDP28x0 is capable of supporting Ultra High-Definition video formats, resolutions as high as 4096 x

2160@60 Hz. It supports RGB/YCbCr video color formats with a color depth of 16 bpc (or 48 bits per

pixel) as long as it fits within the DP1.2a and HDMI2.0b link rate. In addition, this device also supports

pixel encoding conversion from YCbCr444 to YCbCr420 and YcbCr420 pass-through from a DP input to

an HDMI output. High Dynamic Range (HDR) with deep color up to 12bpc at 4Kp60Hz is supported

through the conversion of YCbCr444 CVT timing over DP link with horizontal expansion to YCbCr420

CEA timing on the HDMI TX output.

This device offers secure reception and transmission of high bandwidth digital audio and video content

with HDCP 1.x content protection for the upstream DP interface and HDCP2.2 for the downstream HDMI

interface. It also operates as an HDCP1.x repeater between the source and the sink. In addition, it

conforms to the secure communication protocol specified in the Intel “LSPCON Security Requirements Architecture Specification” document. The MCDP28x0 comes with embedded HDCP keys that are stored in

encrypted form.

The MCDP28x0 uses an external crystal of 27 MHz as a reference clock for its operation and it has a

reset input which provides the chip reset during system power up. The device has an on-chip

microcontroller with SPI, UART, and I2C interfaces for system level communication and debug. It

requires an external SPI flash memory for storing device configuration firmware. The firmware update is

done through the DP AUX channel or through UART interface. An 8 Mbit SPI flash memory is

recommended for storing the firmware with a backup option as fail-safe during in-system-programming.