MC100EP16

Clock Management Design Using Low Skew and Low Jitter Devices

WhyDoWeNeedClockManagement? CanyouimaginethechaosinourworldifourclocksorwatcheswerenotsynchronizedtoGreenwichMeanTime?Howwouldtrains,buses,andairplanesrunonschedule?TheminiseriesLongitudewasthestoryofamanwhomadeamajortechnologicalbreakthroughbyinv

MC100EP16

Differential Driver / Receiver; • 220 ps Propagation Delay\n• Maximum Frequency > 4 GHz Typical (See Graph)\n• PECL Mode Operating Range: VCC = 3.0 V to 5.5 V with VEE = 0 V\n• NECL Mode Operating Range: VCC = 0 V with VEE = -3.0 V to -5.5 V\n• Open Input Default State\n• Safety Clamp on Inputs\n• Q Output Will Default LOW with Inputs Open or at VEE\n• VBB Output\n;

The EP16 is a world-class differential receiver/driver. The device is functionally equivalent to the EL16 and LVEL16 devices with higher performance capabilities. With output transition times significantly faster than the EL16 and LVEL16, the EP16 is ideally suited for interfacing with high frequency sources. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 µF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. Under open input conditions (pulled to VEE ) internal input clamps will force the Q output LOW. The 100 Series contains temperature compensation.

MC100EP16

3.3V / 5V ECL Differential Receiver/Driver

MC100EP16T

Differential Driver / Receiver with Internal Termination; • 220 ps Typical Propagation Delay\n• Maximum Frequency > 3 GHz Typical\n• PECL Mode Operating Range: VCC= 3.0 V to 5.5 V with VEE= 0 V\n• NECL Mode Operating Range: VCC= 0 V with VEE= -3.0 V to -5.5 V\n• Internal 50 Ω Termination Resistors\n;

The EP16T is a world-class differential receiver/driver. The device is functionally equivalent to the EP16 with internal termination resistors. A 50 resistor is connected from the D input to the VT pin and from the Dbar input to the VTbar pin. Tie the VT and VTbar pins to VTT supply (VCC - 2 V) for parallel termination or connect VT and VTbar pins for 100 input series termination.Special considerations are required for differential inputs under No Signal conditions to prevent instability.The 100 Series contains temperature compensation.

MC100EP16TD

3.3V / 5V ECL Differential Receiver/Driver with Internal Termination

Description TheEP16Tisaworld−classdifferentialreceiver/driver.ThedeviceisfunctionallyequivalenttotheEP16withinternalterminationresistors.A50resistorisconnectedfromtheDinputtotheVTpinandfromtheDinputtotheVTpin.TietheVTandVTpinstoVTTsupply(VCC−

MC100EP16TDR2

3.3V / 5V ECL Differential Receiver/Driver with Internal Termination

Description TheEP16Tisaworld−classdifferentialreceiver/driver.ThedeviceisfunctionallyequivalenttotheEP16withinternalterminationresistors.A50resistorisconnectedfromtheDinputtotheVTpinandfromtheDinputtotheVTpin.TietheVTandVTpinstoVTTsupply(VCC−

MC100EP16TDT

3.3V / 5V ECL Differential Receiver/Driver with Internal Termination

Description TheEP16Tisaworld−classdifferentialreceiver/driver.ThedeviceisfunctionallyequivalenttotheEP16withinternalterminationresistors.A50resistorisconnectedfromtheDinputtotheVTpinandfromtheDinputtotheVTpin.TietheVTandVTpinstoVTTsupply(VCC−

MC100EP16TDTR2

3.3V / 5V ECL Differential Receiver/Driver with Internal Termination

Description TheEP16Tisaworld−classdifferentialreceiver/driver.ThedeviceisfunctionallyequivalenttotheEP16withinternalterminationresistors.A50resistorisconnectedfromtheDinputtotheVTpinandfromtheDinputtotheVTpin.TietheVTandVTpinstoVTTsupply(VCC−

MC100EP16VA

差分驱动器/接收器，高增益; • 270 ps Typical Propagation Delay\n• Gain > 20\n• 20 mV Minimum Input Voltage Swing\n• Maximum Frequency > 3 GHz Typical\n• PECL Mode Operating Range: VCC= 3.0 V to 5.5 V with VEE= 0 V\n• NECL Mode Operating Range: VCC= 0 V with VEE= - 3.0 V to - 5.5 V\n• Open Input Default State\n• VBB Output\n;

The EP16VA is a world-class differential receiver/driver. The device is functionally equivalent to the EP16 and LVEP16 devices but with high gain output. QHG and QHGbar outputs have a DC gain several times larger than the DC gain of an EP16.The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 µF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open.Under open input conditions (pulled to VEE) internal input clamps will force the QHG output LOW.Special considerations are required for differential inputs under No Signal conditions to prevent instability.The 100 Series contains temperature compensation.

MC100EP16VAD

3.3V / 5VECL Differential Receiver/Driver with High Gain

Description TheEP16VAisaworld−classdifferentialreceiver/driver.ThedeviceisfunctionallyequivalenttotheEP16andLVEP16devicesbutwithhighgainoutput.QHGandQHGoutputshaveaDCgainseveraltimeslargerthantheDCgainofanEP16. TheVBBpin,aninternallygeneratedvolt