74SSTUB32868ZRHR集成电路（IC）的专用逻辑器件规格书PDF中文资料

74SSTUB32868ZRHR属于集成电路（IC）的专用逻辑器件。由德州仪器制造生产的74SSTUB32868ZRHR专用逻辑器件专用逻辑 IC 设计提供应用特定的逻辑输出类型，例如 BCD 速率倍增、可寻址扫描端口、总线终端阵列、CML 驱动器、比较器、ABT 扫描测试、二进制全加法器、互补对加逆变器、可配置缓冲器、触点颤动消除器、晶体振荡器、延迟元件、差分接收器、LVTTL 到 GTLP 收发器、存储器解码器、电源良好检测器和分频器。

1FEATURES

2· Member of the Texas Instruments

Widebus+ ™Family

· Pinout Optimizes DDR2 DIMM PCB Layout

· 1-to-2 Outputs Supports Stacked DDR2 DIMMs

· One Device Per DIMM Required

· Chip-Select Inputs Gate the Data Outputs from Changing State and Minimizes System Power

Consumption

· Output Edge-Control Circuitry Minimizes

Switching Noise in an Unterminated Line

· Supports SSTL_18 Data Inputs

· Differential Clock (CLK and CLK) Inputs

· Supports LVCMOS Switching Levels on the

Chip-Select Gate-Enable, Control, and RESET

Inputs

· Checks Parity on DIMM-Independent Data

Inputs

· Supports Industrial Temperature Range

(-40°C to 85°C)

· RESET Input Disables Differential Input

Receivers, Resets All Registers, and Forces

All Outputs Low, Except QERR

APPLICATIONS

· DDR2 registered DIMM

DESCRIPTION

This 28-bit 1:2 configurable registered buffer is designed for 1.7-V to 1.9-V VCC operation. One device per DIMM

is required to drive up to 18 SDRAM loads or two devices per DIMM are required to drive up to 36 SDRAM

loads.

All inputs are SSTL_18, except the chip-select gate-enable (CSGEN), control (C), and reset (RESET) inputs,

which are LVCMOS. All outputs are edge-controlled circuits optimized for unterminated DIMM loads, and meet

SSTL_18 specifications, except the open-drain error (QERR) output.

The 74SSTUB32868 operates from a differential clock (CLK and CLK). Data are registered at the crossing of

CLK going high and CLK going low.

The 74SSTUB32868 accepts a parity bit from the memory controller on the parity bit (PAR_IN) input, compares it

with the data received on the DIMM-independent D-inputs (D1−D5, D7, D9−D12, D17−D28 when C = 0; or

D1−D12, D17−D20, D22, D24−D28 when C = 1) and indicates whether a parity error has occurred on the

open-drain QERR pin (active low). The convention is even parity, i.e., valid parity is defined as an even number

of ones across the DIMM-independent data inputs combined with the parity input bit. To calculate parity, all

DIMM-independent D-inputs must be tied to a known logic state.

The 74SSTUB32868 includes a parity checking function. Parity, which arrives one cycle after the data input to

which it applies, is checked on the PAR_IN input of the device. Two clock cycles after the data are registered,

the corresponding QERR signal is generated.