首页>MC908GZ60VFU>规格书详情
MC908GZ60VFU中文资料PDF规格书
MC908GZ60VFU规格书详情
General Description
Introduction
The MC68HC908GZ60, MC68HC908GZ48, and MC68HC908GZ32 are members of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types.
Features
For convenience, features have been organized to reflect:
• Standard features
• Features of the CPU08
Standard Features
Features of the MC68HC908GZ60 include:
• High-performance M68HC08 architecture optimized for C-compilers
• Fully upward-compatible object code with M6805, M146805, and M68HC05 Families
• 8-MHz internal bus frequency
• Clock generation module supporting 1-MHz to 8-MHz crystals
• MSCAN08 (scalable controller area network) controller (implementing 2.0b protocol as defined in BOSCH specification dated September 1991)
• FLASH program memory security(1)
• On-chip programming firmware for use with host personal computer which does not require high voltage for entry
• In-system programming (ISP)
• System protection features:
– Optional computer operating properly (COP) reset
– Low-voltage detection with optional reset and selectable trip points for 3.3-V and 5.0-V operation
– Illegal opcode detection with reset
– Illegal address detection with reset
• Low-power design; fully static with stop and wait modes
• Standard low-power modes of operation:
– Wait mode
– Stop mode
• Master reset pin and power-on reset (POR)
• On-chip FLASH memory:
– MC68HC908GZ60 — 60 Kbytes
– MC68HC908GZ48 — 48 Kbytes
– MC68HC908GZ32 — 32 Kbytes
• Random-access memory (RAM):
– MC68HC908GZ60 — 2048 bytes
– MC68HC908GZ48 — 1536 bytes
– MC68HC908GZ32 — 1536 bytes
• Serial peripheral interface (SPI) module
• Enhanced serial communications interface (ESCI) module
• One 16-bit, 2-channel timer interface module (TIM1) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel
• One 16-bit, 6-channel timer interface module (TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel
• Timebase module with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external crystal
• 24-channel, 10-bit successive approximation analog-to-digital converter (ADC)
• 8-bit keyboard wakeup port with software selectable rising or falling edge detect, as well as high or low level detection
• Up to 53 general-purpose input/output (I/O) pins, including:
– 40 shared-function I/O pins, depending on package choice
– Up to 13 dedicated I/O pins, depending on package choice
• Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis. During output mode, pullups are disengaged.
• Internal pullups on IRQ and RST to reduce customer system cost
• High current 10-mA sink/source capability on all port pins
• Higher current 20-mA sink/source capability on PTC0–PTC4 and PTF0–PTF3
• User selectable clockout feature with divide by 1, 2, and 4 of the bus or crystal frequency
• User selection of having the oscillator enabled or disabled during stop mode
• BREAK module (BRK) to allow single breakpoint setting during in-circuit debugging
• Available packages:
– 32-pin low-profile quad flat pack (LQFP)
– 48-pin low-profile quad flat pack (LQFP)
– 64-pin quad flat pack (QFP)
• Specific features in 32-pin LQFP are:
– Port A is only 4 bits: PTA0–PTA3; shared with ADC and KBI modules
– Port B is only 6 bits: PTB0–PTB5; shared with ADC module
– Port C is only 2 bits: PTC0–PTC1; shared with MSCAN module
– Port D is only 7 bits: PTD0–PTD6; shared with SPI, TIM1 and TIM2 modules
– Port E is only 2 bits: PTE0–PTE1; shared with ESCI module
• Specific features in 48-pin LQFP are:
– Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
– Port B is 8 bits: PTB0–PTB7; shared with ADC module
– Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
– Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, and TIM2 modules
– Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
• Specific features in 64-pin QFP are:
– Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
– Port B is 8 bits: PTB0–PTB7; shared with ADC module
– Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
– Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, andTIM2 modules
– Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
– Port F is 8 bits: PTF0–PTF7; shared with TIM2 module
– Port G is 8 bits; PTG0–PTG7; shared with ADC module
产品属性
- 产品编号:
MC908GZ60VFUE
- 制造商:
NXP USA Inc.
- 类别:
集成电路(IC) > 微控制器
- 系列:
HC08
- 包装:
托盘
- 核心处理器:
HC08
- 内核规格:
8 位
- 速度:
8MHz
- 连接能力:
CANbus,SCI,SPI
- 外设:
LVD,POR,PWM
- 程序存储容量:
60KB(60K x 8)
- 程序存储器类型:
闪存
- RAM 大小:
2K x 8
- 电压 - 供电 (Vcc/Vdd):
3V ~ 5.5V
- 数据转换器:
A/D 24x10b
- 振荡器类型:
内部
- 工作温度:
-40°C ~ 105°C(TA)
- 安装类型:
表面贴装型
- 封装/外壳:
64-QFP
- 供应商器件封装:
64-QFP(14x14)
- 描述:
IC MCU 8BIT 60KB FLASH 64QFP
供应商 | 型号 | 品牌 | 批号 | 封装 | 库存 | 备注 | 价格 |
---|---|---|---|---|---|---|---|
NXP Semiconductors |
20+ |
PQFP-64 |
29860 |
NXP微控制器MCU-可开原型号增税票 |
询价 | ||
FREESCALE |
23+ |
PQFP-64 |
3000 |
全新原装、诚信经营、公司现货销售! |
询价 | ||
NXP |
23+ |
64QFP |
9000 |
原装正品,支持实单 |
询价 | ||
Freescale(飞思卡尔) |
2022+ |
60000 |
原厂原装,假一罚十 |
询价 | |||
NXP/恩智浦 |
23+ |
PQFP-64 |
12700 |
买原装认准中赛美 |
询价 | ||
Freescale(飞思卡尔) |
23+ |
NA/ |
8735 |
原厂直销,现货供应,账期支持! |
询价 | ||
FREESCALE |
2021+ |
4095 |
十年专营原装现货,假一赔十 |
询价 | |||
NXP/恩智浦 |
22+ |
PQFP-64 |
12000 |
只有原装,绝对原装,假一罚十 |
询价 | ||
NXP(恩智浦) |
23+ |
QFP64(14x14) |
7350 |
现货供应,当天可交货!免费送样,原厂技术支持!!! |
询价 | ||
Freescale Semiconductor - NXP |
23+ |
64-QFP |
11200 |
主营:汽车电子,停产物料,军工IC |
询价 |